DIAGNÓSTICOS DA REDE DP VIA CANAL DE DIAGNÓSTICO DA REDE.
BYTES DEFAULT DA REDE DP (TODO O ESCRAVO DP POSSUI):
BYTE 1, 2 e 3 – STATUS INTERNO DO ESCRAVO NA REDE DP
BYTE 4 – ENDEREÇO DO MESTRE DA REDE.
BYTE 5 e 6 – NÚMERO DO ID DO ESCRAVO.
BYTE 7 – QUANTIDADE DE DIAGNÓSTICOS.
BYTES DO DP-B-FEN – SENSE:
BYTE 8 = General Node Diagnostics:
Unit_Diag_Bit(0000)="DP Adress Switch is with problem"
Unit_Diag_Bit(0001)="Node Sensor Supply fail."
Unit_Diag_Bit(0002)="Node Actuator Supply fail."
Unit_Diag_Bit(0003)="Expansor(s) with problem. Check."
Unit_Diag_Bit(0004)="I/O Fault - Short circuit."
Unit_Diag_Bit(0005)="Expansors Sensor Supply fail."
Unit_Diag_Bit(0006)="Expansors Actuator Supply fail."
Unit_Diag_Bit(0007)="Fail on FE-8V valve module."
BYTE 9 e 10 = Expansor Address with problem:
Unit_Diag_Bit(0008)="FE 0 address with problem."
Unit_Diag_Bit(0009)="FE 1 address with problem."
Unit_Diag_Bit(0010)="FE 2 address with problem."
Unit_Diag_Bit(0011)="FE 3 address with problem."
Unit_Diag_Bit(0012)="FE 4 address with problem."
Unit_Diag_Bit(0013)="FE 5 address with problem."
Unit_Diag_Bit(0014)="FE 6 address with problem."
Unit_Diag_Bit(0015)="FE 7 address with problem."
Unit_Diag_Bit(0016)="FE 8 address with problem."
Unit_Diag_Bit(0017)="FE 9 address with problem."
Unit_Diag_Bit(0018)="FE 10 address with problem."
Unit_Diag_Bit(0019)="FE 11 address with problem."
Unit_Diag_Bit(0020)="FE 12 address with problem."
Unit_Diag_Bit(0021)="FE 13 address with problem."
Unit_Diag_Bit(0022)="FE 14 address with problem."
Unit_Diag_Bit(0023)="FE 15 address with problem."
BYTE 11 e 12 = Sensor Supply Expansors with problem:
Unit_Diag_Bit(024)="Sensor Supply - FE 0 problem"
Unit_Diag_Bit(025)="Sensor Supply - FE 1 problem"
Unit_Diag_Bit(026)="Sensor Supply - FE 2 problem"
Unit_Diag_Bit(027)="Sensor Supply - FE 3 problem"
Unit_Diag_Bit(028)="Sensor Supply - FE 4 problem"
Unit_Diag_Bit(029)="Sensor Supply - FE 5 problem"
Unit_Diag_Bit(030)="Sensor Supply - FE 6 problem"
Unit_Diag_Bit(031)="Sensor Supply - FE 7 problem"
Unit_Diag_Bit(032)="Sensor Supply - FE 8 problem"
Unit_Diag_Bit(033)="Sensor Supply - FE 9 problem"
Unit_Diag_Bit(034)="Sensor Supply - FE 10 problem"
Unit_Diag_Bit(035)="Sensor Supply - FE 11 problem"
Unit_Diag_Bit(036)="Sensor Supply - FE 12 problem"
Unit_Diag_Bit(037)="Sensor Supply - FE 13 problem"
Unit_Diag_Bit(038)="Sensor Supply - FE 14 problem"
Unit_Diag_Bit(039)="Sensor Supply - FE 15 problem"
BYTE 13 e 14 = Actuator Supply Expansors with problem:
Unit_Diag_Bit(040)="Actuator Supply - FE 0 problem"
Unit_Diag_Bit(041)="Actuator Supply - FE 1 problem"
Unit_Diag_Bit(042)="Actuator Supply - FE 2 problem"
Unit_Diag_Bit(043)="Actuator Supply - FE 3 problem"
Unit_Diag_Bit(044)="Actuator Supply - FE 4 problem"
Unit_Diag_Bit(045)="Actuator Supply - FE 5 problem"
Unit_Diag_Bit(046)="Actuator Supply - FE 6 problem"
Unit_Diag_Bit(047)="Actuator Supply - FE 7 problem"
Unit_Diag_Bit(048)="Actuator Supply - FE 8 problem"
Unit_Diag_Bit(049)="Actuator Supply - FE 9 problem"
Unit_Diag_Bit(050)="Actuator Supply - FE 10 problem"
Unit_Diag_Bit(051)="Actuator Supply - FE 11 problem"
Unit_Diag_Bit(052)="Actuator Supply - FE 12 problem"
Unit_Diag_Bit(053)="Actuator Supply - FE 13 problem"
Unit_Diag_Bit(054)="Actuator Supply - FE 14 problem"
Unit_Diag_Bit(055)="Actuator Supply - FE 15 problem"
BYTE 15 e 16 = Short circuit on FE module
Unit_Diag_Bit(056)="FE 0 with short circuit on IO"
Unit_Diag_Bit(057)="FE 1 with short circuit on IO"
Unit_Diag_Bit(058)="FE 2 with short circuit on IO"
Unit_Diag_Bit(059)="FE 3 with short circuit on IO"
Unit_Diag_Bit(060)="FE 4 with short circuit on IO"
Unit_Diag_Bit(061)="FE 5 with short circuit on IO"
Unit_Diag_Bit(062)="FE 6 with short circuit on IO"
Unit_Diag_Bit(063)="FE 7 with short circuit on IO"
Unit_Diag_Bit(064)="FE 8 with short circuit on IO"
Unit_Diag_Bit(065)="FE 9 with short circuit on IO"
Unit_Diag_Bit(066)="FE 10 with short circuit on IO"
Unit_Diag_Bit(067)="FE 11 with short circuit on IO"
Unit_Diag_Bit(068)="FE 12 with short circuit on IO"
Unit_Diag_Bit(069)="FE 13 with short circuit on IO"
Unit_Diag_Bit(070)="FE 14 with short circuit on IO"
Unit_Diag_Bit(071)="FE 15 with short circuit on IO"
BYTE 17 = No problem
Unit_Diag_Bit(072)="No problem with FE module."
Unit_Diag_Bit(073)="No problem - Sensor Supply."
Unit_Diag_Bit(074)="No problem - Actuator Supply."
Unit_Diag_Bit(075)="No problem - Short Circuit."
DIAGNÓSTICOS DA REDE DP VIA BYTES DE ENTRADA DO CLP.
BYTE 0:
bit 0 - Monitora se houve mudança de endereço da rede Profibus DP (led NET aceso vermelho).
bit 1 - Monitora a fonte de alimentação do Node(led Sensor Supply aceso vermelho).
bit 2 - Monitora fonte de alimentação Actuator Supply do Node (led Actuator Supply aceso vermelho).
bit 3 - Monitora se os expansores estão ou não alocados na rede (led ES aceso vermelho).
bit 4 - Endereço 0 (LSB).
bit 5 - Endereço 1.
bit 6 - Endereço 2.
bit 7 - Endereço 3 (MSB).
BYTE 1:
Bit 0 - Monitora curto-circuito nos I/Os.
bit 4 - Curto Endereço 0 (LSB).
bit 5 - Curto Endereço 1.
bit 6 - Curto Endereço 2.
bit 7 - Curto Endereço 3 (MSB).
Bit 1 - Indica falha na válvula (somente para modelo FE-8V).
Bit 2 - Monitora a fonte de alimentação dos Expansores (led Sensor Supply aceso vermelho).
Bit 3 - Monitora fonte de alimentação Actuator Supply dos Expansores (led Actuator Supply aceso
vermelho).
BYTE 2:
bit 0 - Fonte Endereço 0 (LSB).
bit 1 - Fonte Endereço 1.
bit 2 - Fonte Endereço 2.
bit 3 - Fonte Endereço 3 (MSB).
OBS: O DIAG. VIA BYTE DE ENTRADA DO CLP É OPCIONAL (PODE-SE
UTILIZAR OU NÃO).
IMPORTANTE: SEMPRE MAPEÁ-LO DEPOIS DO ÚLTIMO EXPANSOR
CONFIGURADO NA REDE (Ex: se o último for o slot 5, colocar diag. no slot 6) !!!
